Ventilation round tee 150/125 is designed for connecting an air duct with a diameter of 150 mm to an air duct at a right angle with a diameter of 125 mm.
A galvanized steel tee is a shaped part designed for branching a line of air ducts (i.e., for branching one air flow into two or combining two flows into one). In order to connect various air ducts to each other and combine them into complex ventilation systems, special shaped products are used - tees.
Name | d1, mm | d2, mm | l1, mm | l2, mm | L, mm | H, mm | p, mm |
Tee 125 | 125< /p> | 125 | 30 | 30 | 165 | 85 | 0.55 |
150 | 125 | 30 | 30 | 165 | 95 | 0.55 | |
Tee 150 | 150 | 30 | 30 | 190 | 95 | 0.55 | |
| Tee 200/125 | 200 | 125 | 30 | 30 | 165 | 120 | 0.55 |
Tee 200/150 | 150 | 30 | 30 | 190 | 120 | 0.55 | |
| Tee 200 | 200 | 30 < /td> | 30 | 240 < /td> | 120 | 0.55 | |
Tee 250/125 | 250 < /td> | 125 | 50 | 30 | 165 | 145 | 0.55 |
Tee 250/150 | 150 | 50 < /td> | 30 | 190 < /td> | 145 | 0.55 | |
Tee 250/200 | 200 | 50 | 30 | 240 | 145 | 0.55 | |
Tee 250 | 250 | 50 | 50 | 290 | 145 | < p align="center">0.55 | |
Tee 315/125 | 315 | 125 | 50 | 30 | 165 | 180 | 0.55 |
Tee 315/150 | 150 | 50 | 30 | 190 | 180 | < p align="center">0.55 | |
Tee 315/200 | 200 | 50 | 30 | 240 | 180 | 0.55 | |
Tee 315/250 | 250 | 50 | < p align="center">50 | 290 | < p align="center">180 | 0.55 | |
Tee 315 | 315 | 50 | < td width="48">355 | < td width="52">0.55 |
Air ducts and fittings are made of galvanized steel with a thickness of: p=0.55 ( - 100-355 mm); p=0 .7 ( - 400-800 mm); p=1.0 ( - 900-1600 mm). To ensure rigidity of air ducts in diameters greater than 315 mm, additional stiffeners are provided (intermediate zig).
This material does not corrode. The element is manufactured with a safety margin, which will allow you to repeatedly disconnect and reattach the tee to the air duct or vice versa.
Advantages of galvanized air ducts:
- strength and high reliability of the system;
- uniform distribution of air flow inside the pipe;
- low noise and vibration levels;
- low resistance to the flow of passing air, leading to a reduction in the cost of pumping it;
- mould and corrosion resistance
- possibility of constructing a straight section of up to 12 m without reducing strength;
- high speed of installation of elements, ease of replacement;
- tightness achieved through high density seams.
Air duct connection:
- nipple using sealant (silicone), fixed with screws or rivets. The nipple is used only for connecting straight sections.
- shaped products are connected using a coupling.
Manufacture of air ducts and products made of galvanized steel to order:
Own production of air ducts and products made of galvanized steel for ventilation, aspiration and air conditioning systems thickness 0.4 - 1 mm:
- Rectangular ducts (rectangular ducts);
- Shaped products (bends, half-bends, inserts, tees, transitions, etc.)
- We carry out selection, calculation of air ducts, design and provide technical consultations
The price on the website is for products made of 0.55 galvanized steel. The cost may vary depending on the thickness of the metal. You can order products of any thickness or buy finished products from 0.55 metal
