Tee 250/150 round ventilation is used to connect an air duct with a diameter of 250 mm to an air duct at a right angle with a diameter of 150 mm.
Advantages of galvanized air ducts:
- strength and high reliability of the system;
- uniform distribution of air flow inside the pipe;
- low noise and vibration levels;
- low resistance to the flow of passing air, leading to a reduction in the cost of pumping it;
- mould and corrosion resistance
- possibility of constructing a straight section of up to 12 m without reducing strength;
- high speed of installation of elements, ease of replacement;
- tightness achieved through high density seams.
A galvanized steel tee is a shaped part designed for branching a line of air ducts (i.e., for branching one air flow into two or combining two flows into one). In order to connect various air ducts to each other and combine them into complex ventilation systems, special shaped products are used - tees.
| Name | d1, mm | d2, mm | l1, mm | l2, mm | L, mm | H, mm | p, mm |
Tee 125 | 125 | 125 | 30 | 30 | 165 | 85 | 0.55 |
Tee 150/125 | 150 | 125 | 30 | 30< /p> | 165 | 95< /p> | 0.55 |
Tee 150 | 150 | 30 | 30 | 190 | 95 | 0.55 | |
Tee 200 /125 | 200 | 125 | 30 | 30 | 165 | 120 | 0.55 |
Tee 200/150 | 150 | 30 | 30 | 190 | 120 | 0.55 | |
Tee 200 | 200 | 30 | 30 | 240 | 120 | 0.55 | |
Tee 250/125 | 250 | 125 | 50 | 30 | 165 | 145 | 0.55 |
Tee 250/150 | 150 | 50 | 30 | 190 | 145 | 0.55 | |
Tee 250/200 | 200 | 50 | 30 | 240 | 145 | 0.55 < /td> | |
Tee 250 | 250 | < p align="center">50 | 50 | < p align="center">290 | 145 | 0.55 | |
Tee 315/125 | < p align="center">315 | 125 | 50 | 30 | 165 | 180 | 0.55 |
Tee 315/150 | 150 | < p align="center">50 | 30 | < p align="center">190 | 180 | 0.55 | |
Tee 315/200 | 200 | 50 | 30 | 240 | 180 | 0.55 | |
Tee 315/250 | < p align="center">250 | 50 | 50 | 290 | 180 | 0.55 | |
Tee 315 | 315 | 50 | 60 | 355 | 180 | 0.55 |
Manufacture of air ducts and products made of galvanized steel to order:
In-house production of air ducts and products made of galvanized steel for aspiration ventilation systems and air conditioning thickness 0.4 - 1 mm:
- Air ducts of rectangular section (rectangular ducts);
- air ducts of circular cross-section, straight-seam (round ducts); < li>Shaped products (bends, half-bends, tie-ins, tees, transitions, etc.)
- We carry out selection, calculation of air ducts, design and provide technical consultations
The price on the website is indicated for products made of 0.55 galvanized steel. The cost may vary depending on the thickness of the metal. You can order products of any thickness or buy ready-made products from 0.55 metal
